Unit 4 review: Elevation, contours and slope

Fill each blank in the session. At home, check each blank with the review handout of unit 4 at remotesensing.fyi, and correct it. Keep this page in your binder, behind the tab of unit 4.

What we learned

  1. The elevation of a point is the height of the ground above mean sea level. is the height above sea level of a thing off the ground, for example an airplane. Read the margin for feet or meters.
  2. A joins points of the same elevation. Closed lines inside each other show a hill.
  3. The is the difference in elevation between two lines next to each other. Every fifth line is a thicker index contour, with its elevation printed on it.
  4. Lines close together show steep land, and lines far apart show gentle land. A is the side view of the land along a line on the map.
  5. Where a line crosses a stream, it bends into a V. A V that points downhill shows a . A closed line with short ticks on its inside edge shows a .
  6. A or a gives the exact elevation of a point between lines.
  7. The slope is the rise divided by the run. The of a stream is often in feet per mile.
  8. A (DEM) is a grid of elevations. SRTM made one with radar.

Traps

  1. Count the spaces, not the lines.

    Do not: divide by the 4 lines between index contours of 500 ft and 600 ft: 100 ÷ 4 = 25 ft.

    Do: divide by the count of the spaces, the lines plus one: 100 ÷ 5 = .

    Drill it: Count the spaces

  2. The next index contour is five lines away.

    Do not: call 1,040 ft the next index contour above 1,000 ft when the lines are 40 ft apart.

    Do: add five spaces: 1,000 + 5 × 40 = .

    Drill it: Count the spaces

  3. Rise over run, not run over rise.

    Do not: divide the run by the rise: for a rise of 60 m over a run of 1,500 m, 1,500 ÷ 60 = 25.

    Do: divide the rise by the run: 60 ÷ 1,500 = .

    Drill it: Slope triangle

  4. Change the run to the ground first.

    Do not: divide a rise of 48 m by a map distance of 4 cm at 1:24,000: 48 ÷ 4 = 12.

    Do: change 4 cm to the ground: 4 × 24,000 = 96,000 cm, or 960 m. Then 48 ÷ 960 = .

    Drill it: Slope triangle

  5. One unit for the rise and the run.

    Do not: divide a rise of 300 ft by a run of 1,000 m: 300 ÷ 1,000 = 0.3.

    Do: change one of them first: 1,000 m is about 3,281 ft, thus 300 ÷ 3,281 is about .

    Drill it: Slope triangle

  6. Which way the V points.

    Do not: read the V at a stream as an arrow that points the way the water flows.

    Do: read it as an arrow that points .

    Drill it: Which way does it flow?

  7. The top is above the last line.

    Do not: give the elevation of the highest closed line, 1,320 ft, as the elevation of the top.

    Do: when the lines are 40 ft apart, give a range: above 1,320 ft and below .

    Drill it: Between the lines

  8. Ticks point down.

    Do not: read a closed line with short ticks on its inside edge as a hilltop.

    Do: read it as a : inside the line, the land is lower, and the water has no outlet.

    Drill it: Read the land

Practice this unit with its flash cards: open remotesensing.fyi, and find unit 4.

main fb25b7f