Unit 4 review: Elevation, contours and slope

What we learned in unit 4, and the traps that cost points. Keep this page in your binder, behind the tab of unit 4.

What we learned

  1. The elevation of a point is the height of the ground above mean sea level. Altitude is the height above sea level of a thing off the ground, for example an airplane. Read the margin for feet or meters.
  2. A contour line joins points of the same elevation. Closed lines inside each other show a hill.
  3. The contour interval is the difference in elevation between two lines next to each other. Every fifth line is a thicker index contour, with its elevation printed on it.
  4. Lines close together show steep land, and lines far apart show gentle land. A profile is the side view of the land along a line on the map.
  5. Where a line crosses a stream, it bends into a V. A V that points downhill shows a ridge. A closed line with short ticks on its inside edge shows a depression.
  6. A spot elevation or a benchmark gives the exact elevation of a point between lines.
  7. The slope is the rise divided by the run. The gradient of a stream is often in feet per mile.
  8. A digital elevation model (DEM) is a grid of elevations. SRTM made one with radar.

Traps

  1. Count the spaces, not the lines.

    Do not: divide by the 4 lines between index contours of 500 ft and 600 ft: 100 ÷ 4 = 25 ft.

    Do: divide by the count of the spaces, the lines plus one: 100 ÷ 5 = 20 ft.

    Drill it: Count the spaces

  2. The next index contour is five lines away.

    Do not: call 1,040 ft the next index contour above 1,000 ft when the lines are 40 ft apart.

    Do: add five spaces: 1,000 + 5 × 40 = 1,200 ft.

    Drill it: Count the spaces

  3. Rise over run, not run over rise.

    Do not: divide the run by the rise: for a rise of 60 m over a run of 1,500 m, 1,500 ÷ 60 = 25.

    Do: divide the rise by the run: 60 ÷ 1,500 = 0.04.

    Drill it: Slope triangle

  4. Change the run to the ground first.

    Do not: divide a rise of 48 m by a map distance of 4 cm at 1:24,000: 48 ÷ 4 = 12.

    Do: change 4 cm to the ground: 4 × 24,000 = 96,000 cm, or 960 m. Then 48 ÷ 960 = 0.05.

    Drill it: Slope triangle

  5. One unit for the rise and the run.

    Do not: divide a rise of 300 ft by a run of 1,000 m: 300 ÷ 1,000 = 0.3.

    Do: change one of them first: 1,000 m is about 3,281 ft, thus 300 ÷ 3,281 is about 0.09.

    Drill it: Slope triangle

  6. Which way the V points.

    Do not: read the V at a stream as an arrow that points the way the water flows.

    Do: read it as an arrow that points upstream.

    Drill it: Which way does it flow?

  7. The top is above the last line.

    Do not: give the elevation of the highest closed line, 1,320 ft, as the elevation of the top.

    Do: when the lines are 40 ft apart, give a range: above 1,320 ft and below 1,360 ft.

    Drill it: Between the lines

  8. Ticks point down.

    Do not: read a closed line with short ticks on its inside edge as a hilltop.

    Do: read it as a depression: inside the line, the land is lower, and the water has no outlet.

    Drill it: Read the land

Practice this unit with its flash cards: open remotesensing.fyi, and find unit 4.

main fb25b7f