The reference pages of unit 4. Keep them behind the Reference tab at the end of your binder, after the index. To find a word, look in the index first.
Elevation and contour lines
Elevation and altitude
The elevation of a point is the height of the ground there above mean sea level.
Altitude is the height of a thing above sea level when it is not on the ground, for example an airplane.
A topographic map gives elevations in feet or in meters. Read the margin to find which.
The height of a thing above the ground is its altitude minus the elevation of the ground below it.
Example: an airplane at an altitude of 4,500 feet flies over ground at an elevation of 1,700 feet. Its height above the ground is 4,500 − 1,700 = 2,800 feet.
Contour lines
A contour line joins points of the same elevation. On a USGS map, contour lines are brown.
A hill is a set of closed lines, one inside the other. The smallest closed line is near the top.
Two contour lines never cross.
Think of water that rises around a hill, one contour interval at a time. At each step, the edge of the water is one more contour line, and every point on that edge has the same elevation.
Elevation from space
A digital elevation model (DEM) is a grid of elevations, one value for each cell.
SRTM, the Shuttle Radar Topography Mission, measured most of the land with radar from the Space Shuttle in February 2000: the land between 60° N and 56° S, with a cell of about 30 m.
A computer draws contour lines and shaded relief from a DEM.
From the map to the side
Think of a hill as a model with one layer for each contour line. Each layer is the land at or above the elevation of its line.
From above, the edge of each layer is a contour line, and the model looks like the map. Tilt the model from the top to the side to see the shape of the hill.
A computer can draw the land as a 3D model from a DEM, and it draws the contour lines from the same grid.
R4-2
Unit 4: Elevation, contours and slope
The elevation of a point
The contour interval
The contour interval is the difference in elevation between two contour lines next to each other. The margin of the map gives it.
Every fifth line is an index contour. It is thicker, and its elevation is printed on it. Thus two index contours next to each other are five intervals apart.
If the margin does not give the interval, find it from two index contours next to each other:
Subtract the elevation of the lower index contour from the elevation of the higher one.
Count the spaces between them: the lines between, plus one.
Divide the difference by the count of the spaces.
The formula: Interval = (the higher index contour − the lower index contour) ÷ the number of spaces between them.
Example: two index contours next to each other are at 625 m and 650 m, with 4 lines between them. The interval is (650 − 625) ÷ (4 + 1) = 5 m.
Line
Elevation
Index contour
625 m
Line 1
630 m
Line 2
635 m
Line 3
640 m
Line 4
645 m
Index contour
650 m
A point between two lines
A point between two lines next to each other is higher than the lower line and lower than the higher line.
Halfway between the lines, estimate the value halfway between their two elevations.
The top of a hill is higher than its highest closed line, and less than one interval above it.
A spot elevation is a point with its elevation printed beside it. A benchmark (BM) is a point that surveyors measured with care. Each one gives the exact elevation of its point.
Example: a point halfway between the 2,560 and 2,640 foot lines, two lines next to each other:
Higher than 2,560 feet and lower than 2,640 feet.
Estimate 2,600 feet, halfway between the lines.
R4-3
Unit 4: Elevation, contours and slope
The shape of the land
Steep, gentle and the profile
Lines close together show steep land. Lines far apart show gentle land.
The slope gives how steep the land is, as a number. Find how to calculate it on page R4-4.
A profile is the side view of the land along a line on the map. To draw one:
Lay a strip of paper along the line on the map. Mark each place where a contour line crosses it, with its elevation.
Move the marks to a graph: distance along the line across, elevation up.
Join the points with a smooth line.
Where the marks are close together, the profile is steep. Where they are far apart, it is gentle.
Streams, ridges and depressions
Where a contour line crosses a stream, it bends into a V, or into a U in a wide valley. The bend points uphill, and along a stream, uphill is upstream.
The water flows the other way: from the higher lines toward the lower lines.
A V that points downhill shows a ridge: a long, narrow strip of high land.
A closed line with short ticks on its inside edge shows a depression: a low area with no outlet.
Which way is up?
The same lines fit a hill and a depression. The lines alone show the shape of the land, but not which way is up.
A printed elevation, the ticks of a depression or water shows which way is up.
A printed elevation is the number on an index contour, a spot elevation or a benchmark.
Water flows downhill, the surface of a lake is flat and low, and the shore of the sea is at 0 feet.
A V alone does not show which way is up. It points uphill in a valley and downhill on a ridge.
Read the land
Read the lines first: their shape, their spacing and their ticks. The landforms of Pixel Peak, the hill of the decks:
Landform
What the lines show
The top
The smallest closed line of the hill, with the spot elevation inside it.
The second top
A smaller set of closed lines, one inside the next, with no elevation printed.
The depression
A closed line with short ticks on its inside edge. The land inside is lower.
The stream valley
Each line bends into a V where it crosses the stream, and each V points upstream.
The steep side
The lines are close together.
The gentle side
The lines are far apart.
R4-4
Unit 4: Elevation, contours and slope
Slope and gradient
Rise over run
The slope between two points is the rise divided by the run:
The rise is the change in elevation between the two points.
The run is the distance on the ground between them.
Use the same unit for the rise and the run. If one is in feet and the other is in meters, change one of them first.
The formula: Slope = rise ÷ run, both in the same unit. Put the rise on top. The run divided by the rise is upside down.
Give a slope as a decimal, or as 1 in a number. That number is the run for a rise of 1.
Example: a stream falls 180 m over a run of 2,400 m. Its slope is 180 ÷ 2,400 = 0.075, or about 1 in 13.
The gradient of a stream
For a stream, the gradient is often given in feet per mile. A mile is 5,280 feet, so the gradient is the slope × 5,280.
The slope has no unit, so this works for a rise and a run in meters too.
Example: the stream above has a slope of 0.075. Its gradient is 0.075 × 5,280 = 396 feet per mile.
Slope from a map
Measure the distance between the two points on the map, and change it to the distance on the ground with the scale. Find how on page R2-2.
Find the elevation of each point, and subtract to get the rise.
Divide the rise by the run. For a gradient, multiply the slope by 5,280.
Example: point A is at 2,150 feet, and point B is at 3,050 feet. On a map at 1:24,000, they are 3 inches apart.