Unit 2 review: Map basics

What we learned in unit 2, and the traps that cost points. Keep this page in your binder, behind the tab of unit 2.

What we learned

  1. The marginal information at the edges of a map gives its location, its date, its scale, its orientation and what its symbols mean. Read this information before you read the map.
  2. At a scale of 1:24,000, 1 cm on the map is 240 m on the ground, and 1 inch is 2,000 feet.
  3. A large scale, such as 1:24,000, shows a small area with much detail. A small scale, such as 1:1,000,000, shows a large area with less detail.
  4. A map gives its scale as a ratio, in words, or as a scale bar. The third form stays true when the map is printed larger or smaller, or shown on a screen, because it changes size with the map.
  5. True north (a star on a USGS map) points to the North Pole. A compass points to magnetic north. The angle between them, the magnetic declination, changes with place and time.
  6. The legend gives the meaning of each symbol and color. On a USGS map: blue for water, green for woods, brown for contour lines, black for most roads and buildings, and red for main roads.
  7. An azimuth is one angle, measured clockwise from north: north is 0° and east is 90°.
  8. A bearing turns from North or South toward East or West. A back azimuth is 180° away.

Traps

  1. Count the zeros.

    Do not: write 150 m or 15 km for 3 cm at 1:50,000.

    Do: write each step. 3 cm × 50,000 = 150,000 cm, and 1 km is 100,000 cm, thus it is 1.5 km.

    Drill it: Map ruler

  2. A map at 1:1,000,000.

    Do not: call 1:1,000,000 the larger scale because 1,000,000 is the larger number.

    Do: read the number after "1:". The larger the number, the smaller the scale.

  3. A ratio is not true on a screen.

    Do not: measure a map on a screen with a ruler, and then use the ratio of the map.

    Do: mark the two points on a strip of paper, and read the distance on the scale bar.

  4. A quarter turn from north.

    Do not: call west 90° because west is a quarter turn from north.

    Do: start at north, 0°, and turn clockwise. East is 90°, south is 180°, and west is 270°.

    Drill it: Azimuth dial

  5. A bearing never has more than 90°.

    Do not: write 230° as "West 40° South" or as "South 230° West".

    Do: count from south (180°) toward west: South (230° − 180°) West = South 50° West.

    Drill it: Bearing builder

  6. The opposite direction.

    Do not: subtract the azimuth from 180°, as in 180° − 40° = 140°.

    Do: if it is under 180°, add 180°: 40° + 180° = 220°. If not, subtract 180°: 330° − 180° = 150°.

    Drill it: There and back

  7. Hold the protractor on north.

    Do not: read the protractor while it turns, or while its 0° does not point to north.

    Do: put the center of the protractor on the start point, turn 0° to north along a grid line or the edge of the map, and hold it still. Then read the degrees where the line to the target crosses the edge.

    Drill it: Place the protractor

  8. An old map.

    Do not: compare two maps, or use the declination of an old map, before you read the margin.

    Do: read the date of each map first, because roads and the declination change with time.

    Drill it: Magnetic declination

Practice this unit with its flash cards: open remotesensing.fyi, and find unit 2.

main fb25b7f